Skip to content

Dehumidifiers and humidifiers

Standalone units that dry or moisten the air. They need no system: inside a system's room they work on that room, and anywhere else (a shed, a basement) they work on the space around them, up to 30 blocks of airflow away by default, the same reach as a vent.

Dehumidifier

Build

An iron block on top of a waxed copper grate, with a sign on the iron block, either on its side or standing on top.

 side view:

 [ iron  ][sign]      or        [sign]
 [ grate ]                      [iron ]
                                [grate]

Look at the sign and run:

/hvac create dehumidifier [label]          ("dehum" works too)

The grate must not already be linked as a water vent (unlink it with the link tool first).

Using it

EZvac | basement
58% > 45%
Running
Tank 40%

Line 2 is the humidity of the space it works on and its setpoint. Line 3 is its state: Running, Idle, OFF, Emptying... or Air too cold.

  • Right-click the sign to open its control menu: the black pane raises the setpoint by 5%, the white one lowers it, from 35% to 60% (the lowest and highest of dehumidifier.presets; 30-50% for a humidifier). A lever in the menu switches it on or off.
  • Sneak-right-click to switch it on or off. Off keeps the tank as it is.
  • It starts 2% above the setpoint and runs until the air is down to it.
  • The water it removes fills its tank. A full tank waterlogs the grate and the sign shows Emptying... for 30 seconds, then it carries on. The water never leaves the grate.
  • Breaking the sign, the iron block or the grate removes it.

"Air too cold"

Air too cold in place of Running means the air is already drier than its coil can dry it: the dew point is at or below 35 °F, as in snowy biomes. Like a real refrigerant dehumidifier it keeps running but removes nothing, and the tank doesn't fill. /hvac info on it explains the same. It clears once the air holds a little more moisture.

Humidifier

Build

A waxed cut copper slab (bottom half) on top of an iron block, with a sign on the side of the iron block.

 side view:

 [ slab ]
 [ iron ][sign]

Look at the sign and run:

/hvac create humidifier [label]            ("hum" works too)

Using it

EZvac | nursery
32% > 40%
Running
Humidifier
  • It works like a dehumidifier the other way round: it starts 2% below its setpoint and runs up to it. Setpoints step through 30, 35, 40, 45, 50%.
  • Right-click and sneak-right-click the sign as for a dehumidifier.
  • It is plumbed: it never runs dry and needs no refilling.
  • While it runs, the slab fills with water and bubbles like water over soul sand. The water never leaves the slab.
  • It adds moisture more slowly as the air nears saturation, and stops short of it.
  • Breaking the sign, the iron block or the slab removes it.

Several units in one space

Units outside a system's room that share air (one's reach covers the air around the other) are one space with one humidity. A dehumidifier and a humidifier in the same shed show the same value on both signs, the HUD and sensors, and work on it together: what they do adds up, and the water the dehumidifiers remove is shared between their tanks. Inside a system's room they already share the room's humidity.

Good to know

  • One unit works at full strength in a space of up to 1,500 blocks, and proportionally slower in bigger ones. Add units for a big hall.
  • /hvac info on a unit shows the space it works on, its humidity, setpoint and state, and a dehumidifier's tank.
  • Using the sign needs ezvac.use; building and removing need ezvac.admin.
  • Tuning is under dehumidifier: and humidifier:; see Configuration.
  • How humidity itself works: Climate.